No products were found matching your selection.

Other Related Products

  • Double Sided Body Tape For Clothes

    • Widths: 1–5 cm; Lengths: 10–50 cm
    • Clear, near-invisible for discreet support
    • Material: acrylic-based adhesive on polyethylene film
    • Thickness: 0.12 mm +/- 0.02 mm
    • Holds well under light sweat conditions
    • Recommended patch test for sensitive skin
    Read moreDone

  • Thermal Break Foam Tape

    • Common size: 25 mm-100 mm width, custom slit rolls available
    • Color: Black, grey, or white closed cell foam
    • Material: PE/XPE closed cell foam with pressure-sensitive adhesive
    • Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
    • Use position: Between roof panels, wall cladding, frames, purlins, and girts
    • Main function: Thermal bridge reduction and condensation control
    Read moreDone

  • EPDM Rubber Adhesive Tape

    • Common thickness: 1 mm to 12 mm
    • Color: black EPDM rubber or cellular rubber
    • Carrier: closed-cell EPDM foam or cellular rubber
    • Adhesive: high-tack acrylic or rubber-based coating
    • Liner: release paper or film liner options
    • Format: slit rolls, gasket strips, die-cut pads
    Read moreDone

  • Double Sided Body Moulding Tape

    • Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
    • Color: Black, grey, or white foam core
    • Material: Acrylic foam or closed cell PE foam
    • Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
    • Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
    • Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
    Read moreDone

  • Adhesive Backed Neoprene Strips

    • Common size: 0.5 mm-10 mm thickness, custom slit widths
    • Color: Black solid neoprene rubber, other colors by review
    • Material: Neoprene rubber, Shore A 50-70 typical
    • Adhesive backing: Acrylic, rubber-based, or LSE PSA
    • Release liner: Paper, PET film, split liner, or finger-lift liner
    • Processing:Slitting, kiss-cut, cut length, and die-cut strips
    Read moreDone

  • Double Coated Cloth Carpet Tape

    • Common width: 12 mm, 24 mm, 48 mm, 50 mm, 100 mm, or made-to-width rolls
    • Common length: 10 m, 25 m, 50 m, 100 m, or jumbo roll converting
    • Color: White, off-white, natural cloth, or liner-dependent appearance
    • Carrier: Cloth/fabric carrier with good tensile support
    • Adhesive: Rubber-based pressure-sensitive adhesive on both sides
    • Liner: Glassine paper, siliconized paper, or PE film release liner
    Read moreDone

  • Foam Tape Jumbo Roll For Automotive Use

    • Roll format: jumbo roll, log roll, slit roll, die-cut strip
    • Common colors: black, white, grey, or custom foam color
    • Foam carrier: PE, IXPE, EVA, or acrylic foam options
    • Adhesive: automotive-grade acrylic pressure sensitive adhesive
    • Liner: PE film, PET film, glassine paper, or release paper
    • Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm
    Read moreDone

  • Two Sided Paper Tape

    • Regular width: 5 mm-1240 mm, slit to requested roll size
    • Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
    • Color: white or translucent adhesive layer with white/yellow liner
    • Material: thin paper-based double-sided adhesive structure
    • Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
    • Liner options: glassine liner, kraft liner, or extended finger-lift liner
    Read moreDone

  • EPDM Sponge Specific Gravity and Density Data

    EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.

    Read moreDone