No products were found matching your selection.

Other Related Products

  • Jumbo Roll Double Sided Tape For Packaging

    • Width: 1020 mm / 1240 mm jumbo roll, custom slit width
    • Thickness: 60-160 um typical reference range
    • Color: white tape with white or yellow release liner
    • Carrier: tissue, non-woven tissue, or optional film carrier
    • Adhesive: hot melt, water-based acrylic, or solvent acrylic
    • Liner: 60-90 gsm release paper for stable peeling
  • Thermal Break Foam Tape

    • Common size: 25 mm-100 mm width, custom slit rolls available
    • Color: Black, grey, or white closed cell foam
    • Material: PE/XPE closed cell foam with pressure-sensitive adhesive
    • Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
    • Use position: Between roof panels, wall cladding, frames, purlins, and girts
    • Main function: Thermal bridge reduction and condensation control
  • Traction Non Slip Rug Strip

    • Common width: 25mm, 50mm, 75mm, 100mm
    • Format: roll strip, slit roll, or pre-cut strip
    • Color: clear, white, black, or translucent gel
    • Material: rubber, PU gel, or polymer traction layer
    • Adhesive side: pressure-sensitive layer for rug backing
    • Thickness: 0.5-2.0mm typical low-profile range
  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

  • EVA Rubber Foam Insulation Tape

    • Foam backing: Closed-cell EVA rubber foam, soft and flexible
    • Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
    • Colors: Black, white, grey, or made-to-order color
    • Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
    • Liner: Release paper, glassine liner, or PET release film
    • Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
  • Double Coated Cloth Carpet Tape

    • Common width: 12 mm, 24 mm, 48 mm, 50 mm, 100 mm, or made-to-width rolls
    • Common length: 10 m, 25 m, 50 m, 100 m, or jumbo roll converting
    • Color: White, off-white, natural cloth, or liner-dependent appearance
    • Carrier: Cloth/fabric carrier with good tensile support
    • Adhesive: Rubber-based pressure-sensitive adhesive on both sides
    • Liner: Glassine paper, siliconized paper, or PE film release liner
  • Self Adhesive Foam Gasket

    • Size: Custom strips, pads, rings, frame gaskets, and punched parts
    • Color: Black, grey, white, or custom production color
    • Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
    • Adhesive: Single-sided pressure sensitive adhesive backing
    • Liner: Paper liner, film liner, extended liner, or pull-tab liner
    • Thickness: Typical 1 mm-20 mm, selected by gap and compression
  • Double Sided Foam Tape Thickness & Technical

    Double sided foam tape thickness is not one universal number. It may mean foam core thickness, finished tape without liner, or total caliper with liner. Density, adhesive build, gauge pressure, compression, surface, load, temperature, and dwell affect how a nominal thickness behaves. Treat values as reference data and confirm the actual assembly by sample testing before full use.

  • Two Sided Paper Tape

    • Regular width: 5 mm-1240 mm, slit to requested roll size
    • Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
    • Color: white or translucent adhesive layer with white/yellow liner
    • Material: thin paper-based double-sided adhesive structure
    • Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
    • Liner options: glassine liner, kraft liner, or extended finger-lift liner