No products were found matching your selection.
Other Related Products
-
- Common thickness:5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm
- Color:Deep black for clean visible edges
- Carrier:Closed-cell black PE foam
- Adhesive:Double sided acrylic or rubber adhesive option
- Liner:Paper or film liner for slitting and die-cutting
- Uses:Signs, badges, trim parts, display frames
-
- Width: 12 mm, 15 mm, 20 mm, 25 mm
- Thickness: 2 mm, 3 mm, 4 mm
- Length: 5 m, 10 m, 15 ft, custom
- Color: Black or dark gray
- Material: High-temperature fiber/felt
- Backing: Self-adhesive with release liner
-
- Regular width: 5 mm-1240 mm, slit to requested roll size
- Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
- Color: white or translucent adhesive layer with white/yellow liner
- Material: thin paper-based double-sided adhesive structure
- Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
- Liner options: glassine liner, kraft liner, or extended finger-lift liner
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
- Common width: 6 mm-25 mm, slit rolls available
- Foam color: Black or white closed-cell foam
- Material: Closed-cell PE/PVC foam
- Adhesive: Pressure-sensitive acrylic adhesive
- Liner: Blue, white, or clear release film
-
- Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
- Color: Black, grey, or white foam core
- Material: Acrylic foam or closed cell PE foam
- Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
- Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
- Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
-
- Common thickness: 0.8 mm, 1.0 mm, 1.2 mm, 1.5 mm
- Common width: 10 mm, 12 mm, 15 mm, 20 mm, 25 mm, 50 mm
- Color options: Clear, white, black
- Carrier: High-density foam or acrylic foam
- Adhesive: Pressure-sensitive acrylic adhesive
- Main use: No-drill indoor mounting on smooth rigid surfaces
