No products were found matching your selection.

Other Related Products

  • Jumbo Roll Double Sided Tape For Packaging

    • Width: 1020 mm / 1240 mm jumbo roll, custom slit width
    • Thickness: 60-160 um typical reference range
    • Color: white tape with white or yellow release liner
    • Carrier: tissue, non-woven tissue, or optional film carrier
    • Adhesive: hot melt, water-based acrylic, or solvent acrylic
    • Liner: 60-90 gsm release paper for stable peeling
    Read moreDone

  • Self Adhesive Foam Gasket

    • Size: Custom strips, pads, rings, frame gaskets, and punched parts
    • Color: Black, grey, white, or custom production color
    • Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
    • Adhesive: Single-sided pressure sensitive adhesive backing
    • Liner: Paper liner, film liner, extended liner, or pull-tab liner
    • Thickness: Typical 1 mm-20 mm, selected by gap and compression
    Read moreDone

  • Synthetic Grass Joining Tape

    • Common Width: 100mm, 150mm, 200mm
    • Roll Length: 5m, 10m, 20m, 50m
    • Color: Green or white liner
    • Carrier: Non-woven fabric
    • Adhesive: Pressure-sensitive adhesive
    • Backing Fit: Latex, PP, PE backing
    Read moreDone

  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

    Read moreDone

  • NBR Rubber Foam Insulation Tape

    • Material: Closed-cell NBR rubber foam
    • Color: Black
    • Adhesive: Pressure-sensitive adhesive backing
    • Liner: Silicone paper or film release liner
    • Thickness: 3mm, 6mm, 9mm, 12mm, or custom
    • Width: 25mm, 38mm, 50mm, 75mm, 100mm, or slit width
    Read moreDone

  • Black Polyethylene Foam Tape

    • Common thickness:5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm
    • Color:Deep black for clean visible edges
    • Carrier:Closed-cell black PE foam
    • Adhesive:Double sided acrylic or rubber adhesive option
    • Liner:Paper or film liner for slitting and die-cutting
    • Uses:Signs, badges, trim parts, display frames
    Read moreDone

  • Polyurethane Foam Mounting Tape

    • Common sizes: 5 mm-980 mm slit rolls, die-cut pads available
    • Color: Black, white, or gray foam options
    • Material: PU foam carrier with acrylic adhesive
    • Structure: Double-sided adhesive with release liner
    • Thickness options: 0.5 mm-3.0 mm typical range
    • Applications: Panel bonding, nameplates, light signage, appliance trim
    Read moreDone

  • Double Coated Cloth Carpet Tape

    • Common width: 12 mm, 24 mm, 48 mm, 50 mm, 100 mm, or made-to-width rolls
    • Common length: 10 m, 25 m, 50 m, 100 m, or jumbo roll converting
    • Color: White, off-white, natural cloth, or liner-dependent appearance
    • Carrier: Cloth/fabric carrier with good tensile support
    • Adhesive: Rubber-based pressure-sensitive adhesive on both sides
    • Liner: Glassine paper, siliconized paper, or PE film release liner
    Read moreDone

  • Closed Cell Foam Glazing Tape

    • Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
    • Common width: 6 mm-25 mm, slit rolls available
    • Foam color: Black or white closed-cell foam
    • Material: Closed-cell PE/PVC foam
    • Adhesive: Pressure-sensitive acrylic adhesive
    • Liner: Blue, white, or clear release film
    Read moreDone