No products were found matching your selection.
Other Related Products
-
- Roll format: jumbo roll, log roll, slit roll, die-cut strip
- Common colors: black, white, grey, or custom foam color
- Foam carrier: PE, IXPE, EVA, or acrylic foam options
- Adhesive: automotive-grade acrylic pressure sensitive adhesive
- Liner: PE film, PET film, glassine paper, or release paper
- Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm
-
EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
- Common width: 25mm, 50mm, 75mm, 100mm
- Format: roll strip, slit roll, or pre-cut strip
- Color: clear, white, black, or translucent gel
- Material: rubber, PU gel, or polymer traction layer
- Adhesive side: pressure-sensitive layer for rug backing
- Thickness: 0.5-2.0mm typical low-profile range
-
- Color: Clear transparent appearance
- Core: Clear acrylic foam core
- Adhesive: Acrylic pressure-sensitive adhesive
- Thickness: 0.25 mm to 2.0 mm typical range
- Liner: PE or PET release film
- Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
-
- Common size: 25 mm-100 mm width, custom slit rolls available
- Color: Black, grey, or white closed cell foam
- Material: PE/XPE closed cell foam with pressure-sensitive adhesive
- Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
- Use position: Between roof panels, wall cladding, frames, purlins, and girts
- Main function: Thermal bridge reduction and condensation control
-
- Common thickness: 0.8 mm, 1.0 mm, 1.2 mm, 1.5 mm
- Common width: 10 mm, 12 mm, 15 mm, 20 mm, 25 mm, 50 mm
- Color options: Clear, white, black
- Carrier: High-density foam or acrylic foam
- Adhesive: Pressure-sensitive acrylic adhesive
- Main use: No-drill indoor mounting on smooth rigid surfaces
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
Double sided foam tape thickness is not one universal number. It may mean foam core thickness, finished tape without liner, or total caliper with liner. Density, adhesive build, gauge pressure, compression, surface, load, temperature, and dwell affect how a nominal thickness behaves. Treat values as reference data and confirm the actual assembly by sample testing before full use.
