No products were found matching your selection.
Other Related Products
-
- Common size: 25 mm-100 mm width, custom slit rolls available
- Color: Black, grey, or white closed cell foam
- Material: PE/XPE closed cell foam with pressure-sensitive adhesive
- Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
- Use position: Between roof panels, wall cladding, frames, purlins, and girts
- Main function: Thermal bridge reduction and condensation control
-
- Common sizes: 5 mm-980 mm slit rolls, die-cut pads available
- Color: Black, white, or gray foam options
- Material: PU foam carrier with acrylic adhesive
- Structure: Double-sided adhesive with release liner
- Thickness options: 0.5 mm-3.0 mm typical range
- Applications: Panel bonding, nameplates, light signage, appliance trim
-
- Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
- Common width: 6 mm-25 mm, slit rolls available
- Foam color: Black or white closed-cell foam
- Material: Closed-cell PE/PVC foam
- Adhesive: Pressure-sensitive acrylic adhesive
- Liner: Blue, white, or clear release film
-
- Common thickness: 50 um, 80 um, 100 um, 125 um, 150 um, 205 um
- Color options: Clear tape, red film liner, yellow paper liner, clear film liner
- Carrier material: Stable PET film carrier
- Adhesive structure: Double coated acrylic pressure-sensitive adhesive
- Supply form: Jumbo roll, slit roll, long roll, sheet, die-cut part
- Applications: Electronics, panels, nameplates, displays, automotive trim
-
- Foam backing: Closed-cell EVA rubber foam, soft and flexible
- Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
- Colors: Black, white, grey, or made-to-order color
- Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
- Liner: Release paper, glassine liner, or PET release film
- Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Common width: 25mm, 50mm, 75mm, 100mm
- Format: roll strip, slit roll, or pre-cut strip
- Color: clear, white, black, or translucent gel
- Material: rubber, PU gel, or polymer traction layer
- Adhesive side: pressure-sensitive layer for rug backing
- Thickness: 0.5-2.0mm typical low-profile range
-
EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.
