No products were found matching your selection.
Other Related Products
-
- Color: Clear transparent appearance
- Core: Clear acrylic foam core
- Adhesive: Acrylic pressure-sensitive adhesive
- Thickness: 0.25 mm to 2.0 mm typical range
- Liner: PE or PET release film
- Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
-
- Common Width: 100mm, 150mm, 200mm
- Roll Length: 5m, 10m, 20m, 50m
- Color: Green or white liner
- Carrier: Non-woven fabric
- Adhesive: Pressure-sensitive adhesive
- Backing Fit: Latex, PP, PE backing
-
EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.
-
- Foam backing: Closed-cell EVA rubber foam, soft and flexible
- Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
- Colors: Black, white, grey, or made-to-order color
- Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
- Liner: Release paper, glassine liner, or PET release film
- Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
-
- Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
- Color: Black, grey, or white foam core
- Material: Acrylic foam or closed cell PE foam
- Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
- Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
- Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
- Common thickness: 1 mm to 12 mm
- Color: black EPDM rubber or cellular rubber
- Carrier: closed-cell EPDM foam or cellular rubber
- Adhesive: high-tack acrylic or rubber-based coating
- Liner: release paper or film liner options
- Format: slit rolls, gasket strips, die-cut pads
-
- Width: 12 mm, 15 mm, 20 mm, 25 mm
- Thickness: 2 mm, 3 mm, 4 mm
- Length: 5 m, 10 m, 15 ft, custom
- Color: Black or dark gray
- Material: High-temperature fiber/felt
- Backing: Self-adhesive with release liner
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
