No products were found matching your selection.
Other Related Products
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
- Width: 1020 mm / 1240 mm jumbo roll, custom slit width
- Thickness: 60-160 um typical reference range
- Color: white tape with white or yellow release liner
- Carrier: tissue, non-woven tissue, or optional film carrier
- Adhesive: hot melt, water-based acrylic, or solvent acrylic
- Liner: 60-90 gsm release paper for stable peeling
-
- Common Width: 100mm, 150mm, 200mm
- Roll Length: 5m, 10m, 20m, 50m
- Color: Green or white liner
- Carrier: Non-woven fabric
- Adhesive: Pressure-sensitive adhesive
- Backing Fit: Latex, PP, PE backing
-
- Common size: 25 mm-100 mm width, custom slit rolls available
- Color: Black, grey, or white closed cell foam
- Material: PE/XPE closed cell foam with pressure-sensitive adhesive
- Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
- Use position: Between roof panels, wall cladding, frames, purlins, and girts
- Main function: Thermal bridge reduction and condensation control
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Color: Clear transparent appearance
- Core: Clear acrylic foam core
- Adhesive: Acrylic pressure-sensitive adhesive
- Thickness: 0.25 mm to 2.0 mm typical range
- Liner: PE or PET release film
- Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
-
- Widths: 1–5 cm; Lengths: 10–50 cm
- Clear, near-invisible for discreet support
- Material: acrylic-based adhesive on polyethylene film
- Thickness: 0.12 mm +/- 0.02 mm
- Holds well under light sweat conditions
- Recommended patch test for sensitive skin
-
- Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
- Color: Black, grey, or white foam core
- Material: Acrylic foam or closed cell PE foam
- Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
- Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
- Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
