No products were found matching your selection.

Other Related Products

  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

    Read moreDone

  • Jumbo Roll Double Sided Tape For Packaging

    • Width: 1020 mm / 1240 mm jumbo roll, custom slit width
    • Thickness: 60-160 um typical reference range
    • Color: white tape with white or yellow release liner
    • Carrier: tissue, non-woven tissue, or optional film carrier
    • Adhesive: hot melt, water-based acrylic, or solvent acrylic
    • Liner: 60-90 gsm release paper for stable peeling
    Read moreDone

  • Black Polyethylene Foam Tape

    • Common thickness:5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm
    • Color:Deep black for clean visible edges
    • Carrier:Closed-cell black PE foam
    • Adhesive:Double sided acrylic or rubber adhesive option
    • Liner:Paper or film liner for slitting and die-cutting
    • Uses:Signs, badges, trim parts, display frames
    Read moreDone

  • Traction Non Slip Rug Strip

    • Common width: 25mm, 50mm, 75mm, 100mm
    • Format: roll strip, slit roll, or pre-cut strip
    • Color: clear, white, black, or translucent gel
    • Material: rubber, PU gel, or polymer traction layer
    • Adhesive side: pressure-sensitive layer for rug backing
    • Thickness: 0.5-2.0mm typical low-profile range
    Read moreDone

  • High Temperature Tape For Smoker

    • Width: 12 mm, 15 mm, 20 mm, 25 mm
    • Thickness: 2 mm, 3 mm, 4 mm
    • Length: 5 m, 10 m, 15 ft, custom
    • Color: Black or dark gray
    • Material: High-temperature fiber/felt
    • Backing: Self-adhesive with release liner
    Read moreDone

  • Thermal Break Foam Tape

    • Common size: 25 mm-100 mm width, custom slit rolls available
    • Color: Black, grey, or white closed cell foam
    • Material: PE/XPE closed cell foam with pressure-sensitive adhesive
    • Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
    • Use position: Between roof panels, wall cladding, frames, purlins, and girts
    • Main function: Thermal bridge reduction and condensation control
    Read moreDone

  • EPDM Rubber Adhesive Tape

    • Common thickness: 1 mm to 12 mm
    • Color: black EPDM rubber or cellular rubber
    • Carrier: closed-cell EPDM foam or cellular rubber
    • Adhesive: high-tack acrylic or rubber-based coating
    • Liner: release paper or film liner options
    • Format: slit rolls, gasket strips, die-cut pads
    Read moreDone

  • Adhesive Backed Neoprene Strips

    • Common size: 0.5 mm-10 mm thickness, custom slit widths
    • Color: Black solid neoprene rubber, other colors by review
    • Material: Neoprene rubber, Shore A 50-70 typical
    • Adhesive backing: Acrylic, rubber-based, or LSE PSA
    • Release liner: Paper, PET film, split liner, or finger-lift liner
    • Processing:Slitting, kiss-cut, cut length, and die-cut strips
    Read moreDone

  • Closed Cell Foam Glazing Tape

    • Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
    • Common width: 6 mm-25 mm, slit rolls available
    • Foam color: Black or white closed-cell foam
    • Material: Closed-cell PE/PVC foam
    • Adhesive: Pressure-sensitive acrylic adhesive
    • Liner: Blue, white, or clear release film
    Read moreDone