No products were found matching your selection.
Other Related Products
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Roll format: jumbo roll, log roll, slit roll, die-cut strip
- Common colors: black, white, grey, or custom foam color
- Foam carrier: PE, IXPE, EVA, or acrylic foam options
- Adhesive: automotive-grade acrylic pressure sensitive adhesive
- Liner: PE film, PET film, glassine paper, or release paper
- Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm
-
EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.
-
- Common thickness: 50 um, 80 um, 100 um, 125 um, 150 um, 205 um
- Color options: Clear tape, red film liner, yellow paper liner, clear film liner
- Carrier material: Stable PET film carrier
- Adhesive structure: Double coated acrylic pressure-sensitive adhesive
- Supply form: Jumbo roll, slit roll, long roll, sheet, die-cut part
- Applications: Electronics, panels, nameplates, displays, automotive trim
-
- Regular width: 5 mm-1240 mm, slit to requested roll size
- Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
- Color: white or translucent adhesive layer with white/yellow liner
- Material: thin paper-based double-sided adhesive structure
- Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
- Liner options: glassine liner, kraft liner, or extended finger-lift liner
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
- Color: Clear transparent appearance
- Core: Clear acrylic foam core
- Adhesive: Acrylic pressure-sensitive adhesive
- Thickness: 0.25 mm to 2.0 mm typical range
- Liner: PE or PET release film
- Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
-
- Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
- Common width: 6 mm-25 mm, slit rolls available
- Foam color: Black or white closed-cell foam
- Material: Closed-cell PE/PVC foam
- Adhesive: Pressure-sensitive acrylic adhesive
- Liner: Blue, white, or clear release film
-
- Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
- Color: Black, grey, or white foam core
- Material: Acrylic foam or closed cell PE foam
- Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
- Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
- Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
