No products were found matching your selection.

Other Related Products

  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

    Read moreDone

  • Thermal Break Foam Tape

    • Common size: 25 mm-100 mm width, custom slit rolls available
    • Color: Black, grey, or white closed cell foam
    • Material: PE/XPE closed cell foam with pressure-sensitive adhesive
    • Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
    • Use position: Between roof panels, wall cladding, frames, purlins, and girts
    • Main function: Thermal bridge reduction and condensation control
    Read moreDone

  • NBR Rubber Foam Insulation Tape

    • Material: Closed-cell NBR rubber foam
    • Color: Black
    • Adhesive: Pressure-sensitive adhesive backing
    • Liner: Silicone paper or film release liner
    • Thickness: 3mm, 6mm, 9mm, 12mm, or custom
    • Width: 25mm, 38mm, 50mm, 75mm, 100mm, or slit width
    Read moreDone

  • High Temperature Tape For Smoker

    • Width: 12 mm, 15 mm, 20 mm, 25 mm
    • Thickness: 2 mm, 3 mm, 4 mm
    • Length: 5 m, 10 m, 15 ft, custom
    • Color: Black or dark gray
    • Material: High-temperature fiber/felt
    • Backing: Self-adhesive with release liner
    Read moreDone

  • Double Coated Cloth Carpet Tape

    • Common width: 12 mm, 24 mm, 48 mm, 50 mm, 100 mm, or made-to-width rolls
    • Common length: 10 m, 25 m, 50 m, 100 m, or jumbo roll converting
    • Color: White, off-white, natural cloth, or liner-dependent appearance
    • Carrier: Cloth/fabric carrier with good tensile support
    • Adhesive: Rubber-based pressure-sensitive adhesive on both sides
    • Liner: Glassine paper, siliconized paper, or PE film release liner
    Read moreDone

  • Closed Cell Foam Glazing Tape

    • Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
    • Common width: 6 mm-25 mm, slit rolls available
    • Foam color: Black or white closed-cell foam
    • Material: Closed-cell PE/PVC foam
    • Adhesive: Pressure-sensitive acrylic adhesive
    • Liner: Blue, white, or clear release film
    Read moreDone

  • EVA Rubber Foam Insulation Tape

    • Foam backing: Closed-cell EVA rubber foam, soft and flexible
    • Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
    • Colors: Black, white, grey, or made-to-order color
    • Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
    • Liner: Release paper, glassine liner, or PET release film
    • Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
    Read moreDone

  • Adhesive Backed Neoprene Strips

    • Common size: 0.5 mm-10 mm thickness, custom slit widths
    • Color: Black solid neoprene rubber, other colors by review
    • Material: Neoprene rubber, Shore A 50-70 typical
    • Adhesive backing: Acrylic, rubber-based, or LSE PSA
    • Release liner: Paper, PET film, split liner, or finger-lift liner
    • Processing:Slitting, kiss-cut, cut length, and die-cut strips
    Read moreDone

  • EPDM Rubber Adhesive Tape

    • Common thickness: 1 mm to 12 mm
    • Color: black EPDM rubber or cellular rubber
    • Carrier: closed-cell EPDM foam or cellular rubber
    • Adhesive: high-tack acrylic or rubber-based coating
    • Liner: release paper or film liner options
    • Format: slit rolls, gasket strips, die-cut pads
    Read moreDone