No products were found matching your selection.
Other Related Products
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
-
- Common thickness: 1 mm to 12 mm
- Color: black EPDM rubber or cellular rubber
- Carrier: closed-cell EPDM foam or cellular rubber
- Adhesive: high-tack acrylic or rubber-based coating
- Liner: release paper or film liner options
- Format: slit rolls, gasket strips, die-cut pads
-
- Common sizes: 5 mm-980 mm slit rolls, die-cut pads available
- Color: Black, white, or gray foam options
- Material: PU foam carrier with acrylic adhesive
- Structure: Double-sided adhesive with release liner
- Thickness options: 0.5 mm-3.0 mm typical range
- Applications: Panel bonding, nameplates, light signage, appliance trim
-
- Width: 1020 mm / 1240 mm jumbo roll, custom slit width
- Thickness: 60-160 um typical reference range
- Color: white tape with white or yellow release liner
- Carrier: tissue, non-woven tissue, or optional film carrier
- Adhesive: hot melt, water-based acrylic, or solvent acrylic
- Liner: 60-90 gsm release paper for stable peeling
-
- Material: Closed-cell NBR rubber foam
- Color: Black
- Adhesive: Pressure-sensitive adhesive backing
- Liner: Silicone paper or film release liner
- Thickness: 3mm, 6mm, 9mm, 12mm, or custom
- Width: 25mm, 38mm, 50mm, 75mm, 100mm, or slit width
-
- Widths: 1–5 cm; Lengths: 10–50 cm
- Clear, near-invisible for discreet support
- Material: acrylic-based adhesive on polyethylene film
- Thickness: 0.12 mm +/- 0.02 mm
- Holds well under light sweat conditions
- Recommended patch test for sensitive skin
-
- Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
- Color: Black, grey, or white foam core
- Material: Acrylic foam or closed cell PE foam
- Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
- Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
- Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
-
- Width: 12 mm, 15 mm, 20 mm, 25 mm
- Thickness: 2 mm, 3 mm, 4 mm
- Length: 5 m, 10 m, 15 ft, custom
- Color: Black or dark gray
- Material: High-temperature fiber/felt
- Backing: Self-adhesive with release liner
