No products were found matching your selection.
Other Related Products
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
- Foam backing: Closed-cell EVA rubber foam, soft and flexible
- Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
- Colors: Black, white, grey, or made-to-order color
- Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
- Liner: Release paper, glassine liner, or PET release film
- Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Widths: 1–5 cm; Lengths: 10–50 cm
- Clear, near-invisible for discreet support
- Material: acrylic-based adhesive on polyethylene film
- Thickness: 0.12 mm +/- 0.02 mm
- Holds well under light sweat conditions
- Recommended patch test for sensitive skin
-
- Common thickness:5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm
- Color:Deep black for clean visible edges
- Carrier:Closed-cell black PE foam
- Adhesive:Double sided acrylic or rubber adhesive option
- Liner:Paper or film liner for slitting and die-cutting
- Uses:Signs, badges, trim parts, display frames
-
- Common thickness: 50 um, 80 um, 100 um, 125 um, 150 um, 205 um
- Color options: Clear tape, red film liner, yellow paper liner, clear film liner
- Carrier material: Stable PET film carrier
- Adhesive structure: Double coated acrylic pressure-sensitive adhesive
- Supply form: Jumbo roll, slit roll, long roll, sheet, die-cut part
- Applications: Electronics, panels, nameplates, displays, automotive trim
-
Double sided foam tape thickness is not one universal number. It may mean foam core thickness, finished tape without liner, or total caliper with liner. Density, adhesive build, gauge pressure, compression, surface, load, temperature, and dwell affect how a nominal thickness behaves. Treat values as reference data and confirm the actual assembly by sample testing before full use.
-
- Common width: 25mm, 50mm, 75mm, 100mm
- Format: roll strip, slit roll, or pre-cut strip
- Color: clear, white, black, or translucent gel
- Material: rubber, PU gel, or polymer traction layer
- Adhesive side: pressure-sensitive layer for rug backing
- Thickness: 0.5-2.0mm typical low-profile range
-
- Color: Clear transparent appearance
- Core: Clear acrylic foam core
- Adhesive: Acrylic pressure-sensitive adhesive
- Thickness: 0.25 mm to 2.0 mm typical range
- Liner: PE or PET release film
- Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
