No products were found matching your selection.
Other Related Products
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
-
- Foam backing: Closed-cell EVA rubber foam, soft and flexible
- Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
- Colors: Black, white, grey, or made-to-order color
- Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
- Liner: Release paper, glassine liner, or PET release film
- Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
-
- Roll format: jumbo roll, log roll, slit roll, die-cut strip
- Common colors: black, white, grey, or custom foam color
- Foam carrier: PE, IXPE, EVA, or acrylic foam options
- Adhesive: automotive-grade acrylic pressure sensitive adhesive
- Liner: PE film, PET film, glassine paper, or release paper
- Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm
-
- Regular width: 5 mm-1240 mm, slit to requested roll size
- Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
- Color: white or translucent adhesive layer with white/yellow liner
- Material: thin paper-based double-sided adhesive structure
- Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
- Liner options: glassine liner, kraft liner, or extended finger-lift liner
-
- Width: 1020 mm / 1240 mm jumbo roll, custom slit width
- Thickness: 60-160 um typical reference range
- Color: white tape with white or yellow release liner
- Carrier: tissue, non-woven tissue, or optional film carrier
- Adhesive: hot melt, water-based acrylic, or solvent acrylic
- Liner: 60-90 gsm release paper for stable peeling
-
- Material: Closed-cell NBR rubber foam
- Color: Black
- Adhesive: Pressure-sensitive adhesive backing
- Liner: Silicone paper or film release liner
- Thickness: 3mm, 6mm, 9mm, 12mm, or custom
- Width: 25mm, 38mm, 50mm, 75mm, 100mm, or slit width
-
- Common thickness: 0.8 mm, 1.0 mm, 1.2 mm, 1.5 mm
- Common width: 10 mm, 12 mm, 15 mm, 20 mm, 25 mm, 50 mm
- Color options: Clear, white, black
- Carrier: High-density foam or acrylic foam
- Adhesive: Pressure-sensitive acrylic adhesive
- Main use: No-drill indoor mounting on smooth rigid surfaces
-
- Common size: 25 mm-100 mm width, custom slit rolls available
- Color: Black, grey, or white closed cell foam
- Material: PE/XPE closed cell foam with pressure-sensitive adhesive
- Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
- Use position: Between roof panels, wall cladding, frames, purlins, and girts
- Main function: Thermal bridge reduction and condensation control
