No products were found matching your selection.
Other Related Products
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
- Foam backing: Closed-cell EVA rubber foam, soft and flexible
- Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
- Colors: Black, white, grey, or made-to-order color
- Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
- Liner: Release paper, glassine liner, or PET release film
- Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.
-
- Common size: 25 mm-100 mm width, custom slit rolls available
- Color: Black, grey, or white closed cell foam
- Material: PE/XPE closed cell foam with pressure-sensitive adhesive
- Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
- Use position: Between roof panels, wall cladding, frames, purlins, and girts
- Main function: Thermal bridge reduction and condensation control
-
- Common Width: 90mm, 100mm, 150mm
- Roll Length: 20m, 25m, 50m
- Color: White, brown, gold paper
- Adhesive: Heat bond hot melt adhesive
- Reinforcement: Glass fiber scrim
- Use: Carpet seams, rug edge joining
-
- Color: Clear transparent appearance
- Core: Clear acrylic foam core
- Adhesive: Acrylic pressure-sensitive adhesive
- Thickness: 0.25 mm to 2.0 mm typical range
- Liner: PE or PET release film
- Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
-
- Regular width: 5 mm-1240 mm, slit to requested roll size
- Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
- Color: white or translucent adhesive layer with white/yellow liner
- Material: thin paper-based double-sided adhesive structure
- Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
- Liner options: glassine liner, kraft liner, or extended finger-lift liner
