No products were found matching your selection.
Other Related Products
-
EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.
-
- Common thickness:5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm
- Color:Deep black for clean visible edges
- Carrier:Closed-cell black PE foam
- Adhesive:Double sided acrylic or rubber adhesive option
- Liner:Paper or film liner for slitting and die-cutting
- Uses:Signs, badges, trim parts, display frames
-
- Regular width: 5 mm-1240 mm, slit to requested roll size
- Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
- Color: white or translucent adhesive layer with white/yellow liner
- Material: thin paper-based double-sided adhesive structure
- Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
- Liner options: glassine liner, kraft liner, or extended finger-lift liner
-
- Widths: 1–5 cm; Lengths: 10–50 cm
- Clear, near-invisible for discreet support
- Material: acrylic-based adhesive on polyethylene film
- Thickness: 0.12 mm +/- 0.02 mm
- Holds well under light sweat conditions
- Recommended patch test for sensitive skin
-
- Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
- Color: Black, grey, or white foam core
- Material: Acrylic foam or closed cell PE foam
- Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
- Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
- Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
-
- Common thickness: 50 um, 80 um, 100 um, 125 um, 150 um, 205 um
- Color options: Clear tape, red film liner, yellow paper liner, clear film liner
- Carrier material: Stable PET film carrier
- Adhesive structure: Double coated acrylic pressure-sensitive adhesive
- Supply form: Jumbo roll, slit roll, long roll, sheet, die-cut part
- Applications: Electronics, panels, nameplates, displays, automotive trim
-
- Common sizes: 5 mm-980 mm slit rolls, die-cut pads available
- Color: Black, white, or gray foam options
- Material: PU foam carrier with acrylic adhesive
- Structure: Double-sided adhesive with release liner
- Thickness options: 0.5 mm-3.0 mm typical range
- Applications: Panel bonding, nameplates, light signage, appliance trim
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
