No products were found matching your selection.
Other Related Products
-
- Roll format: jumbo roll, log roll, slit roll, die-cut strip
- Common colors: black, white, grey, or custom foam color
- Foam carrier: PE, IXPE, EVA, or acrylic foam options
- Adhesive: automotive-grade acrylic pressure sensitive adhesive
- Liner: PE film, PET film, glassine paper, or release paper
- Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm
-
- Color: Clear transparent appearance
- Core: Clear acrylic foam core
- Adhesive: Acrylic pressure-sensitive adhesive
- Thickness: 0.25 mm to 2.0 mm typical range
- Liner: PE or PET release film
- Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
-
- Common thickness: 50 um, 80 um, 100 um, 125 um, 150 um, 205 um
- Color options: Clear tape, red film liner, yellow paper liner, clear film liner
- Carrier material: Stable PET film carrier
- Adhesive structure: Double coated acrylic pressure-sensitive adhesive
- Supply form: Jumbo roll, slit roll, long roll, sheet, die-cut part
- Applications: Electronics, panels, nameplates, displays, automotive trim
-
- Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
- Color: Black, grey, or white foam core
- Material: Acrylic foam or closed cell PE foam
- Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
- Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
- Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
-
- Common width: 25mm, 50mm, 75mm, 100mm
- Format: roll strip, slit roll, or pre-cut strip
- Color: clear, white, black, or translucent gel
- Material: rubber, PU gel, or polymer traction layer
- Adhesive side: pressure-sensitive layer for rug backing
- Thickness: 0.5-2.0mm typical low-profile range
-
- Size: Custom strips, pads, rings, frame gaskets, and punched parts
- Color: Black, grey, white, or custom production color
- Material: EPDM, neoprene, PE, PU, EVA, or silicone foam
- Adhesive: Single-sided pressure sensitive adhesive backing
- Liner: Paper liner, film liner, extended liner, or pull-tab liner
- Thickness: Typical 1 mm-20 mm, selected by gap and compression
-
- Common size: 0.5 mm-10 mm thickness, custom slit widths
- Color: Black solid neoprene rubber, other colors by review
- Material: Neoprene rubber, Shore A 50-70 typical
- Adhesive backing: Acrylic, rubber-based, or LSE PSA
- Release liner: Paper, PET film, split liner, or finger-lift liner
- Processing:Slitting, kiss-cut, cut length, and die-cut strips
-
- Width: 12 mm, 15 mm, 20 mm, 25 mm
- Thickness: 2 mm, 3 mm, 4 mm
- Length: 5 m, 10 m, 15 ft, custom
- Color: Black or dark gray
- Material: High-temperature fiber/felt
- Backing: Self-adhesive with release liner
-
Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.
