No products were found matching your selection.

Other Related Products

  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

    Read moreDone

  • Thermal Break Foam Tape

    • Common size: 25 mm-100 mm width, custom slit rolls available
    • Color: Black, grey, or white closed cell foam
    • Material: PE/XPE closed cell foam with pressure-sensitive adhesive
    • Thickness: 3 mm-12 mm, selected by joint gap and fastener pressure
    • Use position: Between roof panels, wall cladding, frames, purlins, and girts
    • Main function: Thermal bridge reduction and condensation control
    Read moreDone

  • NBR Rubber Foam Insulation Tape

    • Material: Closed-cell NBR rubber foam
    • Color: Black
    • Adhesive: Pressure-sensitive adhesive backing
    • Liner: Silicone paper or film release liner
    • Thickness: 3mm, 6mm, 9mm, 12mm, or custom
    • Width: 25mm, 38mm, 50mm, 75mm, 100mm, or slit width
    Read moreDone

  • Synthetic Grass Joining Tape

    • Common Width: 100mm, 150mm, 200mm
    • Roll Length: 5m, 10m, 20m, 50m
    • Color: Green or white liner
    • Carrier: Non-woven fabric
    • Adhesive: Pressure-sensitive adhesive
    • Backing Fit: Latex, PP, PE backing
    Read moreDone

  • Double Coated Cloth Carpet Tape

    • Common width: 12 mm, 24 mm, 48 mm, 50 mm, 100 mm, or made-to-width rolls
    • Common length: 10 m, 25 m, 50 m, 100 m, or jumbo roll converting
    • Color: White, off-white, natural cloth, or liner-dependent appearance
    • Carrier: Cloth/fabric carrier with good tensile support
    • Adhesive: Rubber-based pressure-sensitive adhesive on both sides
    • Liner: Glassine paper, siliconized paper, or PE film release liner
    Read moreDone

  • Clear Acrylic Foam Tape

    • Color: Clear transparent appearance
    • Core: Clear acrylic foam core
    • Adhesive: Acrylic pressure-sensitive adhesive
    • Thickness: 0.25 mm to 2.0 mm typical range
    • Liner: PE or PET release film
    • Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
    Read moreDone

  • Closed Cell Foam Glazing Tape

    • Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
    • Common width: 6 mm-25 mm, slit rolls available
    • Foam color: Black or white closed-cell foam
    • Material: Closed-cell PE/PVC foam
    • Adhesive: Pressure-sensitive acrylic adhesive
    • Liner: Blue, white, or clear release film
    Read moreDone

  • Black Polyethylene Foam Tape

    • Common thickness:5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm
    • Color:Deep black for clean visible edges
    • Carrier:Closed-cell black PE foam
    • Adhesive:Double sided acrylic or rubber adhesive option
    • Liner:Paper or film liner for slitting and die-cutting
    • Uses:Signs, badges, trim parts, display frames
    Read moreDone

  • Adhesive Backed Neoprene Strips

    • Common size: 0.5 mm-10 mm thickness, custom slit widths
    • Color: Black solid neoprene rubber, other colors by review
    • Material: Neoprene rubber, Shore A 50-70 typical
    • Adhesive backing: Acrylic, rubber-based, or LSE PSA
    • Release liner: Paper, PET film, split liner, or finger-lift liner
    • Processing:Slitting, kiss-cut, cut length, and die-cut strips
    Read moreDone