No products were found matching your selection.

Other Related Products

  • EVA Rubber Foam Insulation Tape

    • Foam backing: Closed-cell EVA rubber foam, soft and flexible
    • Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
    • Colors: Black, white, grey, or made-to-order color
    • Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
    • Liner: Release paper, glassine liner, or PET release film
    • Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
  • Clear Acrylic Foam Tape

    • Color: Clear transparent appearance
    • Core: Clear acrylic foam core
    • Adhesive: Acrylic pressure-sensitive adhesive
    • Thickness: 0.25 mm to 2.0 mm typical range
    • Liner: PE or PET release film
    • Format: Rolls, slit rolls, strips, kiss-cut parts, die-cut pads
  • Double Coated Cloth Carpet Tape

    • Common width: 12 mm, 24 mm, 48 mm, 50 mm, 100 mm, or made-to-width rolls
    • Common length: 10 m, 25 m, 50 m, 100 m, or jumbo roll converting
    • Color: White, off-white, natural cloth, or liner-dependent appearance
    • Carrier: Cloth/fabric carrier with good tensile support
    • Adhesive: Rubber-based pressure-sensitive adhesive on both sides
    • Liner: Glassine paper, siliconized paper, or PE film release liner
  • Double Sided Body Tape For Clothes

    • Widths: 1–5 cm; Lengths: 10–50 cm
    • Clear, near-invisible for discreet support
    • Material: acrylic-based adhesive on polyethylene film
    • Thickness: 0.12 mm +/- 0.02 mm
    • Holds well under light sweat conditions
    • Recommended patch test for sensitive skin
  • Closed Cell Foam Glazing Tape

    • Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
    • Common width: 6 mm-25 mm, slit rolls available
    • Foam color: Black or white closed-cell foam
    • Material: Closed-cell PE/PVC foam
    • Adhesive: Pressure-sensitive acrylic adhesive
    • Liner: Blue, white, or clear release film
  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

  • Synthetic Grass Joining Tape

    • Common Width: 100mm, 150mm, 200mm
    • Roll Length: 5m, 10m, 20m, 50m
    • Color: Green or white liner
    • Carrier: Non-woven fabric
    • Adhesive: Pressure-sensitive adhesive
    • Backing Fit: Latex, PP, PE backing
  • NBR Rubber Foam Insulation Tape

    • Material: Closed-cell NBR rubber foam
    • Color: Black
    • Adhesive: Pressure-sensitive adhesive backing
    • Liner: Silicone paper or film release liner
    • Thickness: 3mm, 6mm, 9mm, 12mm, or custom
    • Width: 25mm, 38mm, 50mm, 75mm, 100mm, or slit width
  • PET Double Sided Tape

    • Common thickness: 50 um, 80 um, 100 um, 125 um, 150 um, 205 um
    • Color options: Clear tape, red film liner, yellow paper liner, clear film liner
    • Carrier material: Stable PET film carrier
    • Adhesive structure: Double coated acrylic pressure-sensitive adhesive
    • Supply form: Jumbo roll, slit roll, long roll, sheet, die-cut part
    • Applications: Electronics, panels, nameplates, displays, automotive trim