No products were found matching your selection.

Other Related Products

  • EPDM Rubber Adhesive Tape

    • Common thickness: 1 mm to 12 mm
    • Color: black EPDM rubber or cellular rubber
    • Carrier: closed-cell EPDM foam or cellular rubber
    • Adhesive: high-tack acrylic or rubber-based coating
    • Liner: release paper or film liner options
    • Format: slit rolls, gasket strips, die-cut pads
  • Adhesive Backed Neoprene Strips

    • Common size: 0.5 mm-10 mm thickness, custom slit widths
    • Color: Black solid neoprene rubber, other colors by review
    • Material: Neoprene rubber, Shore A 50-70 typical
    • Adhesive backing: Acrylic, rubber-based, or LSE PSA
    • Release liner: Paper, PET film, split liner, or finger-lift liner
    • Processing:Slitting, kiss-cut, cut length, and die-cut strips
  • EPDM Sponge Specific Gravity and Density Data

    EPDM sponge specific gravity should be read with apparent density, cell structure, compression behavior, and specimen condition, not as one universal number. This reference applies to cellular EPDM used as sheet, gasket, cushioning substrate, or adhesive-tape backing. Published ranges support comparison only; confirm the tested grade under the intended surface, load, temperature, and process conditions.

  • Foam Tape Jumbo Roll For Automotive Use

    • Roll format: jumbo roll, log roll, slit roll, die-cut strip
    • Common colors: black, white, grey, or custom foam color
    • Foam carrier: PE, IXPE, EVA, or acrylic foam options
    • Adhesive: automotive-grade acrylic pressure sensitive adhesive
    • Liner: PE film, PET film, glassine paper, or release paper
    • Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm
  • Two Sided Paper Tape

    • Regular width: 5 mm-1240 mm, slit to requested roll size
    • Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
    • Color: white or translucent adhesive layer with white/yellow liner
    • Material: thin paper-based double-sided adhesive structure
    • Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
    • Liner options: glassine liner, kraft liner, or extended finger-lift liner
  • Synthetic Grass Joining Tape

    • Common Width: 100mm, 150mm, 200mm
    • Roll Length: 5m, 10m, 20m, 50m
    • Color: Green or white liner
    • Carrier: Non-woven fabric
    • Adhesive: Pressure-sensitive adhesive
    • Backing Fit: Latex, PP, PE backing
  • Double Sided Body Moulding Tape

    • Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
    • Color: Black, grey, or white foam core
    • Material: Acrylic foam or closed cell PE foam
    • Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
    • Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
    • Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
  • Jumbo Roll Double Sided Tape For Packaging

    • Width: 1020 mm / 1240 mm jumbo roll, custom slit width
    • Thickness: 60-160 um typical reference range
    • Color: white tape with white or yellow release liner
    • Carrier: tissue, non-woven tissue, or optional film carrier
    • Adhesive: hot melt, water-based acrylic, or solvent acrylic
    • Liner: 60-90 gsm release paper for stable peeling
  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.