No products were found matching your selection.

Other Related Products

  • Adhesive Backed Neoprene Strips

    • Common size: 0.5 mm-10 mm thickness, custom slit widths
    • Color: Black solid neoprene rubber, other colors by review
    • Material: Neoprene rubber, Shore A 50-70 typical
    • Adhesive backing: Acrylic, rubber-based, or LSE PSA
    • Release liner: Paper, PET film, split liner, or finger-lift liner
    • Processing:Slitting, kiss-cut, cut length, and die-cut strips
  • Closed Cell Foam Glazing Tape

    • Common thickness: 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 6 mm
    • Common width: 6 mm-25 mm, slit rolls available
    • Foam color: Black or white closed-cell foam
    • Material: Closed-cell PE/PVC foam
    • Adhesive: Pressure-sensitive acrylic adhesive
    • Liner: Blue, white, or clear release film
  • Polyurethane Foam Mounting Tape

    • Common sizes: 5 mm-980 mm slit rolls, die-cut pads available
    • Color: Black, white, or gray foam options
    • Material: PU foam carrier with acrylic adhesive
    • Structure: Double-sided adhesive with release liner
    • Thickness options: 0.5 mm-3.0 mm typical range
    • Applications: Panel bonding, nameplates, light signage, appliance trim
  • Traction Non Slip Rug Strip

    • Common width: 25mm, 50mm, 75mm, 100mm
    • Format: roll strip, slit roll, or pre-cut strip
    • Color: clear, white, black, or translucent gel
    • Material: rubber, PU gel, or polymer traction layer
    • Adhesive side: pressure-sensitive layer for rug backing
    • Thickness: 0.5-2.0mm typical low-profile range
  • Synthetic Grass Joining Tape

    • Common Width: 100mm, 150mm, 200mm
    • Roll Length: 5m, 10m, 20m, 50m
    • Color: Green or white liner
    • Carrier: Non-woven fabric
    • Adhesive: Pressure-sensitive adhesive
    • Backing Fit: Latex, PP, PE backing
  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

  • Double Sided Body Tape For Clothes

    • Widths: 1–5 cm; Lengths: 10–50 cm
    • Clear, near-invisible for discreet support
    • Material: acrylic-based adhesive on polyethylene film
    • Thickness: 0.12 mm +/- 0.02 mm
    • Holds well under light sweat conditions
    • Recommended patch test for sensitive skin
  • Heat Bond Carpet Seaming Tape

    • Common Width: 90mm, 100mm, 150mm
    • Roll Length: 20m, 25m, 50m
    • Color: White, brown, gold paper
    • Adhesive: Heat bond hot melt adhesive
    • Reinforcement: Glass fiber scrim
    • Use: Carpet seams, rug edge joining
  • Foam Tape Jumbo Roll For Automotive Use

    • Roll format: jumbo roll, log roll, slit roll, die-cut strip
    • Common colors: black, white, grey, or custom foam color
    • Foam carrier: PE, IXPE, EVA, or acrylic foam options
    • Adhesive: automotive-grade acrylic pressure sensitive adhesive
    • Liner: PE film, PET film, glassine paper, or release paper
    • Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm