No products were found matching your selection.

Other Related Products

  • Two Sided Paper Tape

    • Regular width: 5 mm-1240 mm, slit to requested roll size
    • Common thickness: 0.08 mm-0.16 mm, based on adhesive coat weight
    • Color: white or translucent adhesive layer with white/yellow liner
    • Material: thin paper-based double-sided adhesive structure
    • Adhesive: rubber or acrylic pressure-sensitive adhesive for paper surfaces
    • Liner options: glassine liner, kraft liner, or extended finger-lift liner
  • Double Sided Body Moulding Tape

    • Common Size: 6 mm-1200 mm width, slit rolls or die-cut parts
    • Color: Black, grey, or white foam core
    • Material: Acrylic foam or closed cell PE foam
    • Adhesive Structure: Paint-side adhesive and plastic-part-side adhesive
    • Thickness Options: 0.8 mm, 1.1 mm, 1.5 mm, 2.0 mm
    • Main Use: Wide body moulding, rocker panel, tailgate applique, roof ditch, large cladding
  • Traction Non Slip Rug Strip

    • Common width: 25mm, 50mm, 75mm, 100mm
    • Format: roll strip, slit roll, or pre-cut strip
    • Color: clear, white, black, or translucent gel
    • Material: rubber, PU gel, or polymer traction layer
    • Adhesive side: pressure-sensitive layer for rug backing
    • Thickness: 0.5-2.0mm typical low-profile range
  • Synthetic Grass Joining Tape

    • Common Width: 100mm, 150mm, 200mm
    • Roll Length: 5m, 10m, 20m, 50m
    • Color: Green or white liner
    • Carrier: Non-woven fabric
    • Adhesive: Pressure-sensitive adhesive
    • Backing Fit: Latex, PP, PE backing
  • EVA Rubber Foam Insulation Tape

    • Foam backing: Closed-cell EVA rubber foam, soft and flexible
    • Common thickness: 1 mm, 2 mm, 3 mm, 5 mm, 8 mm, 10 mm
    • Colors: Black, white, grey, or made-to-order color
    • Adhesive: Single-sided or double-sided acrylic / hot melt adhesive
    • Liner: Release paper, glassine liner, or PET release film
    • Formats:Slit rolls, jumbo rolls, strips, pads, and die-cut parts
  • Adhesive Tape Solutions for Foam Converting, Lamination and Die Cutting

    Adhesive tapes for foam converting must do more than create an initial bond. They must laminate cleanly to the foam, stay dimensionally stable through slitting or die cutting, release from the liner at the right moment, and continue performing after the converted part is assembled. This solution is intended for foam gaskets, sealing strips, pads, spacers, vibration-control parts and similar components made from PE, EVA, PU, EPDM, neoprene and other foam substrates. The main risks are poor wet-out, edge lifting, adhesive transfer, foam compression, liner instability and cutting distortion. Selection should therefore balance the foam surface, adhesive construction, carrier, liner, converting method, load and service environment.

  • Double Sided Body Tape For Clothes

    • Widths: 1–5 cm; Lengths: 10–50 cm
    • Clear, near-invisible for discreet support
    • Material: acrylic-based adhesive on polyethylene film
    • Thickness: 0.12 mm +/- 0.02 mm
    • Holds well under light sweat conditions
    • Recommended patch test for sensitive skin
  • PET Double Sided Tape

    • Common thickness: 50 um, 80 um, 100 um, 125 um, 150 um, 205 um
    • Color options: Clear tape, red film liner, yellow paper liner, clear film liner
    • Carrier material: Stable PET film carrier
    • Adhesive structure: Double coated acrylic pressure-sensitive adhesive
    • Supply form: Jumbo roll, slit roll, long roll, sheet, die-cut part
    • Applications: Electronics, panels, nameplates, displays, automotive trim
  • Jumbo Roll Double Sided Tape For Packaging

    • Width: 1020 mm / 1240 mm jumbo roll, custom slit width
    • Thickness: 60-160 um typical reference range
    • Color: white tape with white or yellow release liner
    • Carrier: tissue, non-woven tissue, or optional film carrier
    • Adhesive: hot melt, water-based acrylic, or solvent acrylic
    • Liner: 60-90 gsm release paper for stable peeling